English
Wire Mesh Cable Tray for Data Centers, Telecom Rooms and Base Stations: How to Choose
Created on 11.02
Wire Mesh Cable Tray for Data Centers, Telecom Rooms and Base Stations: How to Choose
Wire mesh cable tray is an open basket of welded steel wire, and it is the most common tray for server rooms, telecom rooms, and base station equipment rooms. The open mesh lets air move around the cables, lets cables leave at any point, and keeps the tray light to hang. The choice that matters most is the material: electro-galvanized for dry indoor rooms, hot-dip galvanized for damp or outdoor routes, and stainless steel 304 or 316 for clean, humid, or corrosive sites. This guide shows where mesh tray fits, how to choose size and material, and the mistakes to avoid.
Why Mesh Tray Suits These Rooms
- Airflow:
- Cable entry anywhere:
- Light weight:
- Easy changes:
- Cut on site:
Which Rooms Use It
Place | Typical use | What matters most |
Data center and server room | Overhead routes above racks and across aisles | Airflow, easy cable changes, clean look |
Telecom room | Overhead routes for fiber, data, and transmission cables | Light load, easy extension, bend radius for fiber |
Base station equipment room | Short overhead or wall-side routes for RF, power, and transmission cables | Dry enclosed room, light load, fast installation |
Building ELV room and riser | Low-voltage cabling above ceilings and in risers | Cost, easy routing, separation from power |
Choosing the Material
Material | Best for | Limits |
Electro-galvanized steel | Dry, enclosed indoor rooms | Thin zinc layer. Not for outdoor, wet, or corrosive sites. Cut ends have no zinc |
Hot-dip galvanized steel | Humid rooms, covered outdoor runs, industrial sites | Heavier coating, higher cost |
Stainless steel 304 | Clean rooms, humid indoor sites, exposed routes where a tidy look matters | Not for strong chloride, such as coastal or salt-spray areas |
Stainless steel 316 | Coastal, chemical, and marine sites | Highest cost |
As a rule, match the material to the room, not to the budget alone. A dry, enclosed equipment room rarely needs more than electro-galvanized tray. A rooftop shelter or a site near the sea needs a heavier finish or stainless steel, because a thin zinc layer will not last there.
How to Choose: 5 Steps
- List the cables.
- Choose the width and depth.
- Check the support spacing.
- Match the material to the environment.
- Plan the finishing details.
Common Mistakes
- Using electro-galvanized tray outdoors.
- Leaving cut wire ends bare.
- Mixing power and data in one basket.
- Ignoring bend radius.
- Treating the mesh as an earth conductor.
- Choosing 304 for a coastal site.
Conclusion
Wire mesh tray gives data centers, telecom rooms, and base stations free airflow, easy cable access, and a light, flexible layout. Choose the material by the room, size the tray by the cables, check the support spacing, and finish the details, such as edge protection and bonding. Final selection should follow your project specification and the applicable standards.
FAQ
Is wire mesh tray better than perforated tray for data centers?
Mesh tray gives more airflow and easier cable entry, and is lighter. Perforated tray is stiffer and gives more support under heavy cable. For light to medium data and fiber loads, mesh is common. For heavy loads, check the load data of each tray.
Which material should I choose for a base station?
For a dry, enclosed equipment room, electro-galvanized mesh tray is usually enough. For outdoor shelters, rooftops, and coastal sites, choose hot-dip galvanized or stainless steel, and 316 near the sea.
Does mesh cable tray need a cover?
Not usually in a clean equipment room. Where dust, falling debris, or sunlight are a concern, a cover or a closed tray may be better. Follow your project specification.
Looking for wire mesh cable tray for a data center, telecom room, or base station? Browse our cable tray range, or email abby@wananelectric.com with your width, depth, length, material, and quantity, and our team will quote the tray with its fittings and supports.
Copyright ©️ 2026, Shenzhen Wanan Industrial Co.,Ltd.. All Rights Reserved. Sitemap | Privacy Policy
Follow Us
Follow Us
E-mail:
+86 18823394830
+86 18823394830
Tel:
abby@wananelectric.com
abby@wananelectric.com
Whatsapp:
+86 18823394830
+86 18823394830
PRODUCT
PRODUCT
Cable Tray
Cable Tray
Metal Electrical Conduit
Metal Electrical Conduit
Room 17A01, Block 1, Yintai Building, No. 15 Huilong Road, Shengping Community, Longcheng Street, Longgang District, Shenzhen City,
Guangdong Province, China
Shenzhen Wanan Industrial Co., Ltd. is a China-based manufacturer of Cable Tray Systems and GI Electrical Conduits, established in 2004.
We manufacture perforated cable trays, cable ladders, cable trunking, galvanized and ZAM cable trays, and EMT, IMC and rigid steel conduits. With 22+ years of manufacturing experience, we provide factory-direct supply, OEM/ODM customization, and technical support for EPC contractors, MEP contractors, distributors, and industrial projects worldwide.
Quick Links
Quick Links
